A公司的QE面试题 (英语水平测试部份).
本帖最后由 jule12 于 2010-3-8 10:38 编辑
一.英译汉. (技术文章)
2.1.2 Test condition II, flat cable
2.1.2.1 A fixture capable of gripping the cable 305 mm (12 in) from the connector with uniform tension of 350 N/m ± 20 N/m (2.0 lb/in ± 0.1 lb/in) of cable width and capable of moving either the cable or connector through an arc of 140° ± 10°; see figure 2, method 2
2.1.2.2 Equipment capable of monitoring current of 100 mA and to indicate a discontinuity of 1 microsecond or longer interruption of current flow.
二. 英译汉.(Email)
As per the SFF8087 spec 2.1rev the dimension D25 (16.5+/-0.1MM) is from Datum B to the edge of the PCB.
From the CPK you supplied last week the measurements taken on 200pcs showed that this dimension is on the low side of the tolerance (i.e. 16.4 to 16.5 mm) As a result the CPK value was less than 1.33 which confirmed the process is out of control. Company A will not accept this so we need to look at ways to address this problem.
三.漢译英.(Email)
出现以下missing label应是人为的撕除.这种撕除的动作应是很小心的,因为UL标签的白色底纸完好无整.粘贴不牢不会出现这样的状况,不会留下白色的底纸.
注:
1.目前还有一个预留名额(截止时间:3/15)
2.简单介绍QE待遇: 工作时间5天8小时,薪资6K-7K/月(税前)
3.工作地点:深圳或东莞
4.学历不限,性别不限,年龄30岁以下.
5.工作性质:直接面对客人,跟进项目,压力大,阵亡率高.
6.工厂性质:法资
7.英语水平只是面试的一部份,有兴趣站内短信.
一.英译汉. (技术文章)
2.1.2 Test condition II, flat cable
2.1.2.1 A fixture capable of gripping the cable 305 mm (12 in) from the connector with uniform tension of 350 N/m ± 20 N/m (2.0 lb/in ± 0.1 lb/in) of cable width and capable of moving either the cable or connector through an arc of 140° ± 10°; see figure 2, method 2
2.1.2.2 Equipment capable of monitoring current of 100 mA and to indicate a discontinuity of 1 microsecond or longer interruption of current flow.
二. 英译汉.(Email)
As per the SFF8087 spec 2.1rev the dimension D25 (16.5+/-0.1MM) is from Datum B to the edge of the PCB.
From the CPK you supplied last week the measurements taken on 200pcs showed that this dimension is on the low side of the tolerance (i.e. 16.4 to 16.5 mm) As a result the CPK value was less than 1.33 which confirmed the process is out of control. Company A will not accept this so we need to look at ways to address this problem.
- []Is it possible for you to modify the tool to have the D25 dimension at the nominal value of 16.5mm[/][]Is it possible that you move the PCB by 0.1mm at the molding stage of the process to ensure the D25 dimension is at the nominal value of 16.5mm[/]
三.漢译英.(Email)
- []Missing label[/]
出现以下missing label应是人为的撕除.这种撕除的动作应是很小心的,因为UL标签的白色底纸完好无整.粘贴不牢不会出现这样的状况,不会留下白色的底纸.
- []No label[/]
注:
1.目前还有一个预留名额(截止时间:3/15)
2.简单介绍QE待遇: 工作时间5天8小时,薪资6K-7K/月(税前)
3.工作地点:深圳或东莞
4.学历不限,性别不限,年龄30岁以下.
5.工作性质:直接面对客人,跟进项目,压力大,阵亡率高.
6.工厂性质:法资
7.英语水平只是面试的一部份,有兴趣站内短信.
先给你顶一下。和我专业不对口！呵呵
2010-03-08 13:43
本问题共 20 个回答，登录后查看全部
登录查看
相关问题
部份胶水无法提供MSDS报告。
12 回答 · 6432 浏览
2003年部份试题
9 回答 · 3489 浏览
2003年部份试题
16 回答 · 4022 浏览
百格测试脱落的5%是指哪一部份的5% ？？
3 回答 · 3460 浏览
本公司ISO14001：2004轉版成功，部份經驗與大家分享！
40 回答 · 8150 浏览
案例：某公司部份产品导入16949，原来的手册可以同时共用吗？
8 回答 · 3187 浏览
2003年质量工程师考题(部份)
1 回答 · 3298 浏览
质量月报包括哪几部份
23 回答 · 5370 浏览
这是一份PPAP文件部份清单，请网友帮助译成中文。
18 回答 · 5920 浏览
数量和交期算不算是质量的一部份
22 回答 · 4057 浏览